ATV31HD11N4
Produits associés
Description du produit
Référence :
ATV31HD11N4 Marque : Schneider Disponibilité : En Stock
Caractéristiques
- ATV31HD11N4
- Characteristics
- variable speed drive ATV31 - 11kW - 500V 3-
- phase supply - EMC filter - IP20
- Main
- Range of product Altivar
- Product or component type Variable speed drive
- Product specific application Simple machine
- Component name ATV31
- Assembly style With heat sink
- EMC filter Integrated
- [Us] rated supply voltage 380...500 V (- 5...5 %)
- Supply frequency 50...60 Hz (- 5...5 %)
- Network number of phases 3 phases
- Motor power kW 11 kW 4 kHz
- Motor power hp 15 hp 4 kHz
- Line current 28.4 A 500 V
- 37.2 A 380 V 1 kA
- Apparent power 25 kVA
- Prospective line Isc 1 kA
- Nominal output current 27.7 A 4 kHz
- Maximum transient current 41.6 A 60 s
- Power dissipation in W 397 W at nominal load
- Asynchronous motor control profile Factory set : constant torque
- Sensorless flux vector control with PWM type motor control signal
- Analogue input number 3
- Complementary
- Product destination Asynchronous motors
- Supply voltage limits 323...550 V
- Network frequency 47.5...63 Hz
- Output frequency 0.0005...0.5 kHz
- Nominal switching frequency 4 kHz
- Jun 12, 2017
- 1
- Disclaimer: This documentation is not intended as a substitute for and is not to be used for determining suitability or reliability of these products for specific user applications
- Switching frequency 2...16 kHz adjustable
- Speed range 1...50
- Transient overtorque 150...170 % of nominal motor torque
- Braking torque 100 % with braking resistor continuously
- 150 % without braking resistor
- <= 150 % during 60 s with braking resistor
- Regulation loop Frequency PI regulator
- Motor slip compensation Adjustable
- Automatic whatever the load
- Suppressable
- Output voltage <= power supply voltage
- Electrical connection Terminal 2.5 mm² AWG 14 Al1, Al2, Al3, AOV, AOC, R1A, R1B, R1C, R2A, R2B, LI1...LI6
- Terminal 2.5 mm² AWG 14 L1, L2, L3, U, V, W, PA, PB, PA/+, PC/-
- Tightening torque 0.6 N.m Al1, Al2, Al3, AOV, AOC, R1A, R1B, R1C, R2A, R2B, LI1...LI6
- 0.8 N.m L1, L2, L3, U, V, W, PA, PB, PA/+, PC/-
- Insulation Electrical between power and control
- Supply Internal supply for logic inputs 19...30 V <= 100 mA overload and short-circuit protection
- Internal supply for reference potentiometer (2.2 to 10 kOhm) 10...10.8 V <= 10 mA overload and
- short-circuit protection
- Analogue input type Configurable current AI3 0...20 mA 250 Ohm
- Configurable voltage AI1 0...10 V 30 V max 30000 Ohm
- Configurable voltage AI2 +/- 10 V 30 V max 30000 Ohm
- Sampling duration 4 ms LI1...LI6 discrete
- 8 ms AI1, AI2, AI3 analog
- Response time 8 ms analog AOV, AOC
- 8 ms discrete R1A, R1B, R1C, R2A, R2B
- Linearity error +/- 0.2 % output
- Analogue output number 2
- Analogue output type Configurable current AOC 0...20 mA 800 Ohm 8 bits
- Configurable voltage AOV 0...10 V 470 Ohm 8 bits
- Discrete input logic Positive logic (source) LI1...LI6, < 5 V (state 0), > 11 V (state 1)
- Logic input not wired LI1...LI4, < 13 V (state 1)
- Negative logic (source) LI1...LI6, > 19 V (state 0)
- Discrete output number 2
- Discrete output type Configurable relay logic R1A, R1B, R1C 1 NO + 1 NC 100000 cycles
- Configurable relay logic R2A, R2B NC 100000 cycles
- Minimum switching current 10 mA 5 V DC R1-R2
- Maximum switching current 2 A 250 V AC inductive, cos phi = 0.4 7 ms R1-R2
- 2 A 30 V DC inductive, cos phi = 0.4 7 ms R1-R2
- 5 A 250 V AC resistive, cos phi = 1 0 ms R1-R2
- 5 A 30 V DC resistive, cos phi = 1 0 ms R1-R2
- Discrete input number 6
- Discrete input type Programmable LI1...LI6 24 V 0...100 mA PLC 3500 Ohm
- Acceleration and deceleration ramps Linear adjustable separately from 0.1 to 999.9 s
- S, U or customized
- Braking to standstill By DC injection
- Protection type Input phase breaks drive
- Line supply overvoltage and undervoltage safety circuits drive
- Line supply phase loss safety function, for three phases supply drive
- Motor phase breaks drive
- Overcurrent between output phases and earth (on power up only) drive
- Overheating protection drive
- Short-circuit between motor phases drive
- Thermal protection motor
- Insulation resistance >= 500 mOhm 500 V DC for 1 minute
- Display type 1 LED red drive voltage
- Four 7-segment display units CANopen bus status
- Time constant 5 ms for reference change
- Frequency resolution 0.1 Hz display unit
- 0.1...100 Hz analog input
- Type of connector 1 RJ45 CANopen via VW3 CANTAP2 adaptor
- 1 RJ45 Modbus
- 2
- Physical interface RS485 multidrop serial link CANopen via VW3 CANTAP2 adaptor
- RS485 multidrop serial link Modbus
- Transmission frame RTU CANopen via VW3 CANTAP2 adaptor
- RTU Modbus
- Transmission rate 10, 20, 50, 125, 250, 500 kbps or 1 Mbps CANopen via VW3 CANTAP2 adaptor
- 4800, 9600 or 19200 bps Modbus
- Number of addresses 1...127 CANopen via VW3 CANTAP2 adaptor
- 1...247 Modbus
- Number of drive 127 CANopen via VW3 CANTAP2 adaptor
- 31 Modbus
- Marking CE
- Operating position Vertical +/- 10 degree
- Outer dimension 330 x 245 x 190 mm
- 390 x 245 x 190 mm
- 405 x 234 x 268 mm
- 555 x 234 x 268 mm
- Product weight 11 kg
- Environment
- Dielectric strength 2410 V DC between earth and power terminals
- 3400 V AC between control and power terminals
- Electromagnetic compatibility 1.2/50 µs - 8/20 µs surge immunity test level 3 IEC 61000-4-5
- Electrical fast transient/burst immunity test level 4 IEC 61000-4-4
- Electrostatic discharge immunity test level 3 IEC 61000-4-2
- Radiated radio-frequency electromagnetic field immunity test level 3 IEC 61000-4-3
- Standards EN 50178
- Product certifications CSA
- C-Tick
- N998
- UL
- IP degree of protection IP20 on upper part without cover plate
- IP21 on connection terminals
- IP31 on upper part
- IP41 on upper part
- Pollution degree 2
- Protective treatment TC
- Vibration resistance 1 gn 13...150 Hz EN/IEC 60068-2-6
- 1.5 mm 3...13 Hz EN/IEC 60068-2-6
- Shock resistance 15 gn 11 ms EN/IEC 60068-2-27
- Relative humidity 5...95 % without condensation IEC 60068-2-3
- 5...95 % without dripping water IEC 60068-2-3
- Ambient air temperature for storage -25...70 °C
- Ambient air temperature for operation -10...50 °C without derating with protective cover on top of the drive
- -10...60 °C with derating factor without protective cover on top of the drive
- Operating altitude <= 1000 m without derating
- >= 1000 m with current derating 1 % per 100 m
- Contractual warranty
- Warranty period 18 months
- Product Life Status END-OF-SALE NOTICE
- 3
Avis
Produits qui pourraient aussi répondre à vos besoins
Produits Similaires
Produits similaires
Produits récemment consultés
Aucun produit récemment consulté à afficher
![Logo](https://seniadz.net/wp-content/uploads/2019/10/logo_2018.jpg")