ATV61HD18N4

Fiche technique du produit PDF :

Demander un devis pour de plus grandes quantités

ATV61 18,5 kW 25HP 480V 3 phases EMC IP20 with graphic term

Description

Référence :
ATV61HD18N4 Marque : Schneider Disponibilité : En Stock

Caractéristiques

ATV61HD18N4
Characteristics
ATV61 18,5 kW 25HP 480V 3 phases EMC IP20
with graphic term
Main
Range of product Altivar 61
Product or component type Variable speed drive
Product specific application Pumping and ventilation machine
Component name ATV61
Motor power kW 18.5 kW 3 phases at 380...480 V
Motor power hp 25 hp 3 phases at 380...480 V
[Us] rated supply voltage 380...480 V (- 15...10 %)
Network number of phases 3 phases
Line current 37.5 A for 480 V 3 phases 18.5 kW / 25 hp
45.5 A for 380 V 3 phases 18.5 kW / 25 hp
EMC filter Level 3 EMC filter
Assembly style With heat sink
Apparent power 29.9 kVA for 380 V 3 phases 18.5 kW / 25 hp
Prospective line Isc 22 kA 3 phases
Maximum transient current 49.2 A for 60 s 3 phases
Nominal switching frequency 12 kHz
Switching frequency 1...16 kHz adjustable
12...16 kHz with derating factor
Asynchronous motor control Voltage/frequency ratio, 2 points
profile Voltage/frequency ratio, 5 points
Flux vector control without sensor, standard
Voltage/frequency ratio - Energy Saving, quadratic
U/f
Synchronous motor control profile Vector control without sensor, standard
Communication port protocol CANopen
Modbus
Type of polarization No impedance for Modbus
Option card APOGEE FLN communication card
BACnet communication card
CC-Link communication card
Controller inside programmable card
DeviceNet communication card
Ethernet/IP communication card
Fipio communication card
I/O extension card
Interbus-S communication card
LonWorks communication card
METASYS N2 communication card
Modbus Plus communication card
Modbus TCP communication card
Modbus/Uni-Telway communication card
Multi-pump card
Profibus DP communication card
Profibus DP V1 communication card
Complementary
Product destination Asynchronous motors
Synchronous motors
Supply voltage limits 323...528 V
Supply frequency 50...60 Hz (- 5...5 %)
Network frequency 47.5...63 Hz
Continuous output current 34 A at 12 kHz, 460 V 3 phases
41 A at 12 kHz, 380 V 3 phases
Output frequency 0.1...599 kHz
Speed range 1...100 in open-loop mode, without speed feedback
1 / 4
The information provided in this documentation contains general descriptions and/or technical characteristics of the performance of the products contained herein.
This documentation is not intended as a substitute for and is not to be used for determining suitability or reliability of these products for specific user applications.
It is the duty of any such user or integrator to perform the appropriate and complete risk analysis, evaluation and testing of the products with respect to the relevant specific application or use thereof.
Neither Schneider Electric Industries SAS nor any of its affiliates or subsidiaries shall be responsible or liable for misuse of the information contained herein.
Speed accuracy +/- 10 % of nominal slip for 0.2 Tn to Tn torque variation without speed feedback
Torque accuracy +/- 15 % in open-loop mode, without speed feedback
Transient overtorque 130 % of nominal motor torque, +/- 10 % for 60 s
Braking torque 30 % without braking resistor
<= 125 % with braking resistor
Regulation loop Frequency PI regulator
Motor slip compensation Adjustable
Automatic whatever the load
Can be suppressed
Not available in voltage/frequency ratio (2 or 5 points)
Local signalling 1 LED red presence of drive voltage
Output voltage <= power supply voltage
Isolation Between power and control terminals
Type of cable With an IP21 or an IP31 kit : 3-strand IEC cable at 40 °C, copper 70 °C PVC
Without mounting kit : 1-strand IEC cable at 45 °C, copper 70 °C PVC
Without mounting kit : 1-strand IEC cable at 45 °C, copper 90 °C XLPE/EPR
With UL Type 1 kit : 3-strand UL 508 cable at 40 °C, copper 75 °C PVC
Electrical connection AI1-/AI1+, AI2, AO1, R1A, R1B, R1C, R2A, R2B, LI1...LI6, PWR terminal 2.5 mm² /
AWG 14
L1/R, L2/S, L3/T, U/T1, V/T2, W/T3, PC/-, PO, PA/+, PA, PB terminal 25 mm² / AWG 3
Tightening torque AI1-/AI1+, AI2, AO1, R1A, R1B, R1C, R2A, R2B, LI1...LI6, PWR 0.6 N.m
L1/R, L2/S, L3/T, U/T1, V/T2, W/T3, PC/-, PO, PA/+, PA, PB 5.4 N.m / 47.7 lb.in
Supply Internal supply for reference potentiometer (1 to 10 kOhm) 10.5 V DC +/- 5 %, <= 10
mA for overload and short-circuit protection
Internal supply for reference potentiometer (1 to 10 kOhm) 10.5 V DC +/- 5 %, <= 10
mA for overload and short-circuit protection
Internal supply 24 V DC (21...27 V), <= 200 mA for overload and short-circuit
protection
External supply 24 V DC (19...30 V)
Analogue input number 2
Analogue input type AI1-/Al1+ bipolar differential voltage +/- 10 V DC, input voltage 24 V max, resolution 11
bits + sign
AI2 software-configurable current 0...20 mA, impedance 242 Ohm, resolution 11 bits
AI2 software-configurable voltage 0...10 V DC, input voltage 24 V max, impedance
30000 Ohm, resolution 11 bits
Sampling duration Analog input AI1-/Al1+ 2 ms, +/- 0.5 ms
Analog input Al2 2 ms, +/- 0.5 ms
Analog output AO1 2 ms, +/- 0.5 ms
Discrete input LI1...LI5 2 ms, +/- 0.5 ms
Discrete input LI6 (if configured as logic input) 2 ms, +/- 0.5 ms
Accuracy AI1-/Al1+ +/- 0.6 % for a temperature variation 60 °C
AI2 +/- 0.6 % for a temperature variation 60 °C
AO1 +/- 1 % for a temperature variation 60 °C
Linearity error AI1-/Al1+ +/- 0.15 % of maximum value
AI2 +/- 0.15 % of maximum value
AO1 +/- 0.2 %
Analogue output number 1
Analogue output type AO1 software-configurable current, analogue output range 0...20 mA, impedance 500
Ohm, resolution 10 bits
AO1 software-configurable logic output 10 V, <= 20 mA
AO1 software-configurable voltage, analogue output range 0...10 V DC, impedance
470 Ohm, resolution 10 bits
Discrete output number 2
Discrete output type (R1A, R1B, R1C) configurable relay logic NO/NC, electrical durability 100000 cycles
(R2A, R2B) configurable relay logic NO, electrical durability 100000 cycles
Response time <= 100 ms in STO (Safe Torque Off)
R1A, R1B, R1C <= 7 ms, tolerance +/- 0.5 ms
R2A, R2B <= 7 ms, tolerance +/- 0.5 ms
Minimum switching current Configurable relay logic 3 mA at 24 V DC
Maximum switching current R1, R2 on resistive load, 5 A at 30 V DC, cos phi = 1, 0 ms
R1, R2 on inductive load, 2 A at 30 V DC, cos phi = 0.4, 7 ms
R1, R2 on resistive load, 5 A at 250 V AC, cos phi = 1, 0 ms
R1, R2 on inductive load, 2 A at 250 V AC, cos phi = 0.4, 7 ms
Discrete input number 7
Discrete input type (LI1...LI5) programmable, 24 V DC, voltage limits <= 30 V, with level 1 PLC,
impedance 3500 Ohm
(LI6) switch-configurable, 24 V DC, voltage limits <= 30 V, with level 1 PLC,
impedance 3500 Ohm
2 / 4
(LI6) switch-configurable PTC probe, 0...6, impedance 1500 Ohm
(PWR) safety input, 24 V DC, voltage limits <= 30 V, impedance 1500 Ohm
Discrete input logic LI1...LI5 positive logic (source), < 5 V (state 0), > 11 V (state 1)
LI1...LI5 negative logic (sink), > 16 V (state 0), < 10 V (state 1) LI6 (if configured as logic input) negative logic (sink), > 16 V (state 0), < 10 V (state 1)
LI6 (if configured as logic input) positive logic (source), < 5 V (state 0), > 11 V (state 1)
Acceleration and deceleration ramps Automatic adaptation of ramp if braking capacity exceeded, by using resistor
Linear adjustable separately from 0.01 to 9000 s
S, U or customized
Braking to standstill By DC injection
Protection type Drive against exceeding limit speed
Drive against input phase loss
Drive break on the control circuit
Drive input phase breaks
Drive line supply overvoltage
Drive line supply undervoltage
Drive overcurrent between output phases and earth
Drive overheating protection
Drive overvoltages on the DC bus
Drive power removal
Drive short-circuit between motor phases
Drive thermal protection
Motor motor phase break
Motor power removal
Motor thermal protection
Insulation resistance > 1 mOhm at 500 V DC for 1 minute to earth
Frequency resolution Analog input 0.024/50 Hz
Display unit 0.1 Hz
Type of connector 1 RJ45 for Modbus on front face
1 RJ45 for Modbus on terminal
Male SUB-D 9 on RJ45 for CANopen
Physical interface 2-wire RS 485 for Modbus
Transmission frame RTU for Modbus
Transmission rate 20 kbps, 50 kbps, 125 kbps, 250 kbps, 500 kbps, 1 Mbps for CANopen
4800 bps, 9600 bps, 19200 bps, 38.4 Kbps for Modbus on terminal
4800 bps, 9600 bps, 19200 bps, 38.4 Kbps for Modbus on terminal
9600 bps, 19200 bps for Modbus on front face
Data format 8 bits, 1 stop, even parity for Modbus on front face
8 bits, odd even or no configurable parity for Modbus on terminal
Number of addresses 1...247 for Modbus
1...127 for CANopen
Method of access Slave for CANopen
Marking CE
Operating position Vertical +/- 10 degree
Product weight 22 kg
Width 230 mm
Height 400 mm
Depth 213 mm
Environment
noise level 60.2 dB conforming to 86/188/EEC
dielectric strength 3535 V DC between earth and power terminals
5092 V DC between control and power terminals
electromagnetic compatibility Conforming to IEC 61000-4-2 level 3
Conforming to IEC 61000-4-11
Conforming to IEC 61000-4-6 level 3
Conforming to IEC 61000-4-3 level 3
Conforming to IEC 61000-4-4 level 4
standards EN 55011 class A group 2
EN 61800-3 environments 1 category C3
EN 61800-3 environments 2 category C3
EN/IEC 61800-3
EN/IEC 61800-5-1
IEC 60721-3-3 class 3C1
IEC 60721-3-3 class 3S2
UL Type 1
product certifications CSA
3 / 4
C-Tick
DNV
GOST
NOM 117
UL
pollution degree 2 conforming to EN/IEC 61800-5-1
IP degree of protection IP20 on upper part without blanking plate on cover conforming to EN/IEC 60529
IP20 on upper part without blanking plate on cover conforming to EN/IEC 61800-5-1
IP21 conforming to EN/IEC 60529
IP21 conforming to EN/IEC 61800-5-1
IP41 on upper part conforming to EN/IEC 60529
IP41 on upper part conforming to EN/IEC 61800-5-1
IP54 on lower part conforming to EN/IEC 60529
IP54 on lower part conforming to EN/IEC 61800-5-1
vibration resistance 1.5 mm peak to peak (f = 3...13 Hz) conforming to EN/IEC 60068-2-6
1 gn (f = 13...200 Hz) conforming to EN/IEC 60068-2-6
shock resistance 15 gn for 11 ms conforming to EN/IEC 60068-2-27
relative humidity 5...95 % without condensation conforming to IEC 60068-2-3
5...95 % without dripping water conforming to IEC 60068-2-3
ambient air temperature for operation -10...50 °C without derating
50...60 °C with derating factor
ambient air temperature for storage -25...70 °C
operating altitude <= 1000 m without derating
1000...3000 m with current derating 1 % per 100 m
Contractual warranty
Warranty period 18 months
4 / 4