ATV61HU75N4

Référence :

ATV61HU75N4 Marque : Schneider Disponibilité : En Stock

• ATV61HU75N4
• Characteristics
• ATV61 7,5 kW 10HP 480V 3 phases EMC IP20 with
• graph term
• Main
• Range of product Altivar 61
• Product or component type Variable speed drive
• Product specific application Pumping and ventilation machine
• Component name ATV61
• Motor power kW 7.5 kW 3 phases at 380...480 V
• Motor power hp 10 hp 3 phases at 380...480 V
• [Us] rated supply voltage 380...480 V (- 15...10 %)
• Network number of phases 3 phases
• Line current 22.2 A for 480 V 3 phases 7.5 kW / 10 hp
• 27 A for 380 V 3 phases 7.5 kW / 10 hp
• EMC filter Level 3 EMC filter
• Assembly style With heat sink
• Apparent power 17.8 kVA for 380 V 3 phases 7.5 kW / 10 hp
• Prospective line Isc 22 kA 3 phases
• Maximum transient current 21.1 A for 60 s 3 phases
• Nominal switching frequency 12 kHz
• Switching frequency 1...16 kHz adjustable
• 12...16 kHz with derating factor
• Asynchronous motor control Voltage/frequency ratio, 2 points
• profile Voltage/frequency ratio, 5 points
• Flux vector control without sensor, standard
• Voltage/frequency ratio - Energy Saving, quadratic
• U/f
• Synchronous motor control profile Vector control without sensor, standard
• Communication port protocol CANopen
• Modbus
• Type of polarization No impedance for Modbus
• Option card APOGEE FLN communication card
• BACnet communication card
• CC-Link communication card
• Controller inside programmable card
• DeviceNet communication card
• Ethernet/IP communication card
• Fipio communication card
• I/O extension card
• Interbus-S communication card
• LonWorks communication card
• METASYS N2 communication card
• Modbus Plus communication card
• Modbus TCP communication card
• Modbus/Uni-Telway communication card
• Multi-pump card
• Profibus DP communication card
• Profibus DP V1 communication card
• Complementary
• Product destination Asynchronous motors
• Synchronous motors
• Supply voltage limits 323...528 V
• Supply frequency 50...60 Hz (- 5...5 %)
• Network frequency 47.5...63 Hz
• Continuous output current 14 A at 12 kHz, 460 V 3 phases
• 17.6 A at 12 kHz, 380 V 3 phases
• Output frequency 0.1...599 kHz
• Speed range 1...100 in open-loop mode, without speed feedback
• 1 / 4
• The information provided in this documentation contains general descriptions and/or technical characteristics of the performance of the products contained herein.
• This documentation is not intended as a substitute for and is not to be used for determining suitability or reliability of these products for specific user applications.
• It is the duty of any such user or integrator to perform the appropriate and complete risk analysis, evaluation and testing of the products with respect to the relevant specific application or use thereof.
• Neither Schneider Electric Industries SAS nor any of its affiliates or subsidiaries shall be responsible or liable for misuse of the information contained herein.
• Speed accuracy +/- 10 % of nominal slip for 0.2 Tn to Tn torque variation without speed feedback
• Torque accuracy +/- 15 % in open-loop mode, without speed feedback
• Transient overtorque 130 % of nominal motor torque, +/- 10 % for 60 s
• Braking torque 30 % without braking resistor
• <= 125 % with braking resistor
• Regulation loop Frequency PI regulator
• Motor slip compensation Adjustable
• Automatic whatever the load
• Can be suppressed
• Not available in voltage/frequency ratio (2 or 5 points)
• Local signalling 1 LED red presence of drive voltage
• Output voltage <= power supply voltage
• Isolation Between power and control terminals
• Type of cable With an IP21 or an IP31 kit : 3-strand IEC cable at 40 °C, copper 70 °C PVC
• Without mounting kit : 1-strand IEC cable at 45 °C, copper 70 °C PVC
• Without mounting kit : 1-strand IEC cable at 45 °C, copper 90 °C XLPE/EPR
• With UL Type 1 kit : 3-strand UL 508 cable at 40 °C, copper 75 °C PVC
• Electrical connection AI1-/AI1+, AI2, AO1, R1A, R1B, R1C, R2A, R2B, LI1...LI6, PWR terminal 2.5 mm² /
• AWG 14
• L1/R, L2/S, L3/T, U/T1, V/T2, W/T3, PC/-, PO, PA/+, PA, PB terminal 6 mm² / AWG 8
• Tightening torque L1/R, L2/S, L3/T, U/T1, V/T2, W/T3, PC/-, PO, PA/+, PA, PB 3 N.m / 26.5 lb.in
• AI1-/AI1+, AI2, AO1, R1A, R1B, R1C, R2A, R2B, LI1...LI6, PWR 0.6 N.m
• Supply Internal supply for reference potentiometer (1 to 10 kOhm) 10.5 V DC +/- 5 %, <= 10
• mA for overload and short-circuit protection
• Internal supply for reference potentiometer (1 to 10 kOhm) 10.5 V DC +/- 5 %, <= 10
• mA for overload and short-circuit protection
• Internal supply 24 V DC (21...27 V), <= 200 mA for overload and short-circuit
• protection
• External supply 24 V DC (19...30 V)
• Analogue input number 2
• Analogue input type AI1-/Al1+ bipolar differential voltage +/- 10 V DC, input voltage 24 V max, resolution 11
• bits + sign
• AI2 software-configurable current 0...20 mA, impedance 242 Ohm, resolution 11 bits
• AI2 software-configurable voltage 0...10 V DC, input voltage 24 V max, impedance
• 30000 Ohm, resolution 11 bits
• Sampling duration Analog input AI1-/Al1+ 2 ms, +/- 0.5 ms
• Analog input Al2 2 ms, +/- 0.5 ms
• Analog output AO1 2 ms, +/- 0.5 ms
• Discrete input LI1...LI5 2 ms, +/- 0.5 ms
• Discrete input LI6 (if configured as logic input) 2 ms, +/- 0.5 ms
• Accuracy AI1-/Al1+ +/- 0.6 % for a temperature variation 60 °C
• AI2 +/- 0.6 % for a temperature variation 60 °C
• AO1 +/- 1 % for a temperature variation 60 °C
• Linearity error AI1-/Al1+ +/- 0.15 % of maximum value
• AI2 +/- 0.15 % of maximum value
• AO1 +/- 0.2 %
• Analogue output number 1
• Analogue output type AO1 software-configurable current, analogue output range 0...20 mA, impedance 500
• Ohm, resolution 10 bits
• AO1 software-configurable logic output 10 V, <= 20 mA
• AO1 software-configurable voltage, analogue output range 0...10 V DC, impedance
• 470 Ohm, resolution 10 bits
• Discrete output number 2
• Discrete output type (R1A, R1B, R1C) configurable relay logic NO/NC, electrical durability 100000 cycles
• (R2A, R2B) configurable relay logic NO, electrical durability 100000 cycles
• Response time <= 100 ms in STO (Safe Torque Off)
• R1A, R1B, R1C <= 7 ms, tolerance +/- 0.5 ms
• R2A, R2B <= 7 ms, tolerance +/- 0.5 ms
• Minimum switching current Configurable relay logic 3 mA at 24 V DC
• Maximum switching current R1, R2 on resistive load, 5 A at 30 V DC, cos phi = 1, 0 ms
• R1, R2 on inductive load, 2 A at 30 V DC, cos phi = 0.4, 7 ms
• R1, R2 on resistive load, 5 A at 250 V AC, cos phi = 1, 0 ms
• R1, R2 on inductive load, 2 A at 250 V AC, cos phi = 0.4, 7 ms
• Discrete input number 7
• Discrete input type (LI1...LI5) programmable, 24 V DC, voltage limits <= 30 V, with level 1 PLC,
• impedance 3500 Ohm
• (LI6) switch-configurable, 24 V DC, voltage limits <= 30 V, with level 1 PLC,
• impedance 3500 Ohm
• 2 / 4
• (LI6) switch-configurable PTC probe, 0...6, impedance 1500 Ohm
• (PWR) safety input, 24 V DC, voltage limits <= 30 V, impedance 1500 Ohm
• Discrete input logic LI1...LI5 positive logic (source), < 5 V (state 0), > 11 V (state 1)
• LI1...LI5 negative logic (sink), > 16 V (state 0), < 10 V (state 1) LI6 (if configured as logic input) negative logic (sink), > 16 V (state 0), < 10 V (state 1)
• LI6 (if configured as logic input) positive logic (source), < 5 V (state 0), > 11 V (state 1)
• Acceleration and deceleration ramps Automatic adaptation of ramp if braking capacity exceeded, by using resistor
• Linear adjustable separately from 0.01 to 9000 s
• S, U or customized
• Braking to standstill By DC injection
• Protection type Drive against exceeding limit speed
• Drive against input phase loss
• Drive break on the control circuit
• Drive input phase breaks
• Drive line supply overvoltage
• Drive line supply undervoltage
• Drive overcurrent between output phases and earth
• Drive overheating protection
• Drive overvoltages on the DC bus
• Drive power removal
• Drive short-circuit between motor phases
• Drive thermal protection
• Motor motor phase break
• Motor power removal
• Motor thermal protection
• Insulation resistance > 1 mOhm at 500 V DC for 1 minute to earth
• Frequency resolution Analog input 0.024/50 Hz
• Display unit 0.1 Hz
• Type of connector 1 RJ45 for Modbus on front face
• 1 RJ45 for Modbus on terminal
• Male SUB-D 9 on RJ45 for CANopen
• Physical interface 2-wire RS 485 for Modbus
• Transmission frame RTU for Modbus
• Transmission rate 20 kbps, 50 kbps, 125 kbps, 250 kbps, 500 kbps, 1 Mbps for CANopen
• 4800 bps, 9600 bps, 19200 bps, 38.4 Kbps for Modbus on terminal
• 4800 bps, 9600 bps, 19200 bps, 38.4 Kbps for Modbus on terminal
• 9600 bps, 19200 bps for Modbus on front face
• Data format 8 bits, 1 stop, even parity for Modbus on front face
• 8 bits, odd even or no configurable parity for Modbus on terminal
• Number of addresses 1...247 for Modbus
• 1...127 for CANopen
• Method of access Slave for CANopen
• Marking CE
• Operating position Vertical +/- 10 degree
• Product weight 5.5 kg
• Width 175 mm
• Height 295 mm
• Depth 187 mm
• Environment
• noise level 55.6 dB conforming to 86/188/EEC
• dielectric strength 3535 V DC between earth and power terminals
• 5092 V DC between control and power terminals
• electromagnetic compatibility Conforming to IEC 61000-4-2 level 3
• Conforming to IEC 61000-4-11
• Conforming to IEC 61000-4-6 level 3
• Conforming to IEC 61000-4-3 level 3
• Conforming to IEC 61000-4-4 level 4
• standards EN 55011 class A group 2
• EN 61800-3 environments 1 category C3
• EN 61800-3 environments 2 category C3
• EN/IEC 61800-3
• EN/IEC 61800-5-1
• IEC 60721-3-3 class 3C1
• IEC 60721-3-3 class 3S2
• UL Type 1
• product certifications CSA
• 3 / 4
• C-Tick
• DNV
• GOST
• NOM 117
• UL
• pollution degree 2 conforming to EN/IEC 61800-5-1
• IP degree of protection IP20 on upper part without blanking plate on cover conforming to EN/IEC 60529
• IP20 on upper part without blanking plate on cover conforming to EN/IEC 61800-5-1
• IP21 conforming to EN/IEC 60529
• IP21 conforming to EN/IEC 61800-5-1
• IP41 on upper part conforming to EN/IEC 60529
• IP41 on upper part conforming to EN/IEC 61800-5-1
• IP54 on lower part conforming to EN/IEC 60529
• IP54 on lower part conforming to EN/IEC 61800-5-1
• vibration resistance 1.5 mm peak to peak (f = 3...13 Hz) conforming to EN/IEC 60068-2-6
• 1 gn (f = 13...200 Hz) conforming to EN/IEC 60068-2-6
• shock resistance 15 gn for 11 ms conforming to EN/IEC 60068-2-27
• relative humidity 5...95 % without condensation conforming to IEC 60068-2-3
• 5...95 % without dripping water conforming to IEC 60068-2-3
• ambient air temperature for operation -10...50 °C without derating
• 50...60 °C with derating factor
• ambient air temperature for storage -25...70 °C
• operating altitude <= 1000 m without derating
• 1000...3000 m with current derating 1 % per 100 m
• Contractual warranty
• Warranty period 18 months
• 4 / 4